========================================

RangeLAN2 753x Token Ring Access Point

Flash Code Image           v TR 1.2-B5

README.TXT file

(c)1999  Proxim, Inc.

========================================



HOW TO UPGRADE THE ACCESS POINT'S FLASH CODE VIA A SERIAL CONNECTION



This README file describes how to upgrade the Token Ring Access Point's 

flash code version from an earlier version, such as TR 1.1-B22, to the 

most recent version, TR 1.2-B5, using an RS-232 serial connection.



There are several methods available to download the new image file to the 

Access Point.  To download the image to the Access Point on the network, 

either send the file from an FTP or TFTP server on your network.  

Alternatively, you may send the file over a null modem cable using a 

terminal emulation program following the directions below. Once the new image 

is loaded on one of your Token Ring Access Points, you can send it to the other 

Access Points from the updated Access Point.  Refer to the RangeLAN2 Token Ring

Access Point User's Guide for additional information on this feature.



Follow the steps below to download the new image to a RangeLAN2 Token Ring Access 

Point using a null modem cable and a terminal emulation program, such as 

HyperTerminal which comes pre-installed as an accessory to Windows 95, 98, and NT.  



1.  Download the file 30IMAGE.EXE from the Proxim Support web site at 

http://www.proxim.com/support/ to a folder on a PC's hard drive or to a diskette.



2.  30IMAGE.EXE is a self-extracting file.  Double-click 30IMAGE.EXE to extract 

out TR1-2B5.IMG, which is the image file that needs to be uploaded to the Access Point.



3.  Connect one end of a null modem cable to the Access Point and the other end 

to a PC.  A null modem cable is an RS-232 serial cable that has the transmit and 

receive pins crossed.  Most electronic stores sell null modem cables.

 

4.  Open a terminal emulation program, such as HyperTerminal, and create a session 

using the following settings:  



Connect: Direct to COM port # (use the COM port number that corresponds to the port

that the cable is connected to, typically COM1 or COM2)

Baud Rate: 9600

Data bits: 8

Stop bits: 1

Parity: None

Flow Control: None



5.  Press <Enter> to call up the AP's configuration menu.

 

6.  Choose Option 4, the Download Menu.

 

7.  Choose Option 1, Download Image Using XMODEM.

 

8.  At this point, a series of "C"s will appear on the terminal screen.  

Go to the terminal program's Transfer menu and choose the "Send File" option.

 

9.  Browse the location of TR1-2B5.IMG and configure the protocol type to "XMODEM."

Hit <Send> to begin the transfer.

 

The transfer will take between 10 and 15 minutes.  

The Access Point will reboot itself following the download and will report 

"Initialization Complete" when it ready for use.  You should then confirm that the 

flash code version is now TR 1.2-B5.  The flash code version is reported within the 

Access Point's Diagnostics Menu when connected via serial or telnet and it is also 

reported under the System Information heading within the RangeLAN2 Manager web 

browser tool. 

  



HOW TO CONTACT PROXIM TECHNICAL SUPPORT



You can reach Proxim Technical Support by voice, fax, e-mail, 

mail, or over the Internet:



	Tel: 1-800-477-6946 or 408-731-2640

	Fax: 408-731-3676

	Web: http://www.proxim.com/support/

	e-mail: support@proxim.com

	Mail: Send correspondence to:



		Proxim, Inc.

		Attn: Proxim Technical Support

		510 DeGuigne Drive

		Sunnyvale, CA  94086

		



========================================

(c)1999  Proxim, Inc.

========================================

